www.baldormotion.com

Operation 5-3MN1941

5.2 Starting the NextMove e100

If you have followed the instructions in the previous sections, you should have now connected

the power sources, inputs and outputs and the USB, serial, or Ethernet cable linking the PC to the

NextMove e100.

5.2.1 Preliminary checks

Before you apply power for the first time, it is very important to verify the following:

H Disconnect the load from the motor until instructed to apply a load.

H Inspect all power connections for accuracy, workmanship and tightness.

H Verify that all wiring conforms to applicable codes.

H Verify that the NextMove e100 is properly earthed/grounded.

H Check all signal wiring for accuracy.

5.2.2 Power on checks

1. Turn on the 24 VDC control supply.

2. Within approximately 20-30 seconds or less, the test sequence should complete and the

Status LED should start to flash green. If the Status LED is not lit then re-check the power

supply connections. If the Status LED flashes red, this indicates that the NextMove e100 has

detected a fault - see section 6.

5.2.3 Installing the USB driver

If you have connected the NextMove e100 to the PC using the USB connection, it will be

necessary to install the USB driver. When the NextMove e100 is powered, Windows (2000 or XP

only) will automatically detect the controller and request the driver . The driver consists of two

files, USBmotion.inf and USBmotion.sys. Both files must be present for installation.

1. Follow the on-screen instructions to select and install the driver. The driver files are available

on the supplied Baldor Motion Toolkit CD. If you are using a copy of the driver located on the

hard disk, a floppy disk or another CD, the two driver files must be in the same folder.

2. During installation, Windows XP may report that the driver is ‘unsigned’. This is normal for the

NextMove e100 driver, so click the Continue Anyway button to continue with the installation.

When installation is complete, a new USB Motion Controller device will be listed in the

Universal Serial Bus controllers section of Windows Device Manager .

The NextMove e100 is now ready to be configured using MMC and Mint WorkBench.

Note: If the NextMove e100 is later connected to a different USB port on the host computer,

Windows may report that it has found new hardware. Either install the driver files

again for the new USB port, or connect the NextMove e100 to the original USB port

where it will be recognized in the usual way.

1 2 ... 48 49 50 51 52 53 54 55 56 57 58 ... 113 114

Commentaires sur ces manuels

Pas de commentaire

Home Decorators Collection 7143110820 manuels

Manuels d'utilisation et guides de l'utilisateur pour Non Home Decorators Collection 7143110820.
Nous fournissons des manuels en pdf 1 Home Decorators Collection 7143110820 à télécharger gratuitement par type de document : Manuel d'instructions

Home decorators collection 7143110820 Manuel d'instructions (1 pages)

marque: Home-decorators-collection | Catégorie: No info | Taille: 0.07 MB |

Table des matières

',2:

Plus de produits et de manuels pour Non Home Decorators Collection

Modèles	Type de document
2048100410	Manuel d'instructions Home Decorators Collection 2048100410 Instructions / Assembly, 10 pages
1599400810	Manuel d'instructions Home Decorators Collection 1599400810 Instructions / Assembly, 1 pages
0277200250	Manuel d'instructions Home Decorators Collection 0277200250 Instructions / Assembly, 3 pages
2877420210	Manuel d'instructions Home Decorators Collection 2877420210 Instructions / Assembly, 9 pages
0147910250	Manuel d'instructions Home Decorators Collection 0147910250 Instructions / Assembly, 3 pages
2944200410	Manuel d'instructions Home Decorators Collection 2944200410 Instructions / Assembly, 11 pages
0803900440	Manuel d'instructions Home Decorators Collection 0803900440 Instructions / Assembly, 10 pages
0287700270	Manuel d'instructions Home Decorators Collection 0287700270 Instructions / Assembly, 2 pages
1601200480	Manuel d'instructions Home Decorators Collection 1601200480 Instructions / Assembly, 1 pages
4451540210	Manuel d'instructions Home Decorators Collection 4451540210 Instructions / Assembly, 1 pages
5020700210	Manuel d'instructions Home Decorators Collection 5020700210 Instructions / Assembly, 16 pages
DS5981BK	Guide d'installation Home Decorators Collection DS5981BK Installation Guide, 1 pages
0550500410	Manuel d'instructions Home Decorators Collection 0550500410 Instructions / Assembly, 3 pages
0876000800	Manuel d'instructions Home Decorators Collection 0876000800 Instructions / Assembly, 18 pages
0280600270	Manuel d'instructions Home Decorators Collection 0280600270 Instructions / Assembly, 1 pages
1833600950	Manuel d'instructions Home Decorators Collection 1833600950 Instructions / Assembly, 1 pages
0876100800	Manuel d'instructions Home Decorators Collection 0876100800 Instructions / Assembly, 10 pages
0218010150	Manuel d'instructions Home Decorators Collection 0218010150 Instructions / Assembly, 2 pages
2649430580	Manuel d'instructions Home Decorators Collection 2649430580 Instructions / Assembly, 1 pages
HB7054A-35	Manuel d'instructions Home Decorators Collection HB7054A-35 Instructions / Assembly, 16 pages

Axis E100 Spécifications Page 53

Commentaires sur ces manuels

Produits connexes et manuels pour Serveurs Axis E100

Home Decorators Collection 7143110820 manuels

Home decorators collection 7143110820 Manuel d'instructions (1 pages)

Table des matières

Plus de produits et de manuels pour Non Home Decorators Collection