Axis E100 Spécifications Page 23
- Page / 114
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
www.baldormotion.com
Input / Output 4-7MN1941
4.3 Digital I/O
The NextMove e100 provides:
H 20 general purpose digital inputs.
H 12 general purpose digital outputs.
H 1 general purpose relay output.
4.3.1 Digital inputs
Digital inputs are available on connectors X8, X9 and X10, as shown in section 4.1.1.
The digital inputs are arranged in three groups, each with their own common connection. This
allows each group to be configured independently for ‘active high’ or ‘active low’ operation (using
the Mint INPUTMODE keyword).
The general purpose digital inputs DIN0 - DIN19 can be shared between axes, and are
programmable in Mint (using a range of keywords beginning with the letters INPUT... ) to
determine their active level and if they should be edge triggered. The state of individual inputs can
be read directly using the INX and INSTATEX keywords. See the Mint help file.
A general purpose digital input can be assigned to a special purpose function such as a home,
limit, stop or error input. See the keywords HOMEINPUT, LIMITFORWARDINPUT,
LIMITREVERSEINPUT, STOPINPUT and ERRORINPUT in the Mint help file.
4.3.1.1 DIN0 - DIN3
Digital inputs DIN0 to DIN3 can be assigned as fast interrupts. These are used as high speed
position latches, allowing any combination of axes to be captured by the hardware. The latency
between input triggering and capture is 1 μs. Special Mint keywords (beginning with the letters
LATCH...) allow specific functions to be performed as a result of fast position inputs becoming
active. See the Mint help file for details.
DIN3
6k2
TLP115A
DGND
Mint
Vcc
NextMove e100
CREF0
100R
1
3
Shield 2
‘X10’
Figure 8 - Fast interrupt digita l input - DIN3 shown
Digital inputs DIN0 to DIN3 use CREF0 as their common connection.
Note: The fast inputs are particularly sensitive to noise, so inputs must use shielded
twisted pair cable. Do not connect mechanical switches, relay contacts or other
sources liable to signal ‘bounce’ directly to the fast inputs. This could cause
unwanted multiple triggering.
- Contents 3
- Appendices 5
- General Information 7
- Safety Notice 8
- Precautions 8
- 2.1 NextMove e100 features 9
- 2-2 Introduction MN1941 10
- 2.2 Receiving an d inspection 11
- 2.3 Units an d abbreviations 12
- 3.1 Introduction 13
- 3-2 Basic Installation MN1941 14
- Basic Installa tion 3-3MN1941 15
- 3-4 Basic Installation MN1941 16
- 4.1 Introduction 17
- 4.1.1 Connector locations 18
- 4.2 Analog I/O 19
- 4-4 Input / Output MN1941 20
- 4.2.2 Analog outputs 21
- 4-6 Input / Output MN1941 22
- 4.3 Digital I/O 23
- 4-8 Input / Output MN1941 24
- Input / Output 4-9MN1941 25
- 4-10 Input / Output MN1941 26
- Input / Output 4-11MN1941 27
- 4-12 Input / Output MN1941 28
- Input / Output 4-13MN1941 29
- 4-14 Input / Output MN1941 30
- 4.4 Other I/O 31
- 4-16 Input / Output MN1941 32
- Input / Output 4-17MN1941 33
- 4-18 Input / Output MN1941 34
- Input / Output 4-19MN1941 35
- 4.5.1 USB port 36
- 4.5.2 Serial port 37
- 4.5.3 Using RS232 37
- 4-22 Input / Output MN1941 38
- Input / Output 4-23MN1941 39
- 4.6 Ethernet in terface 40
- 4.6.2 ETHERNET Powerlink 41
- 4.6.3 Ethernet connectors 42
- 4.7 CAN in terface 43
- 4.7.3 CANopen 44
- Input / Output 4-29MN1941 45
- 4-30 Input / Output MN1941 46
- Input / Output 4-31MN1941 47
- 4-32 Input / Output MN1941 48
- Input / Output 4-33MN1941 49
- 4-34 Input / Output MN1941 50
- 5.1 Introduction 51
- 5-2 Operation MN1941 52
- 5.2.1 Preliminary checks 53
- 5.2.2 Power on checks 53
- 5-4 Operation MN1941 54
- 5.3 Mint Machine Center 55
- 5-6 Operation MN1941 56
- 5.3.1 Starting MMC 57
- 5-8 Operation MN1941 58
- 5.4 Mint WorkBench 59
- 5.4.1 Help file 60
- 5.4.2 Starting Mint WorkBench 61
- 5-12 Operation MN1941 62
- 5.5 Configuring axes 63
- 5.5.2 Configuring remote axes 64
- Operation 5-15MN1941 65
- 5.5.3 Configuring local axes 66
- 5.5.4 Selecting a scale 67
- 5-18 Operation MN1941 68
- Operation 5-19MN1941 69
- 5-20 Operation MN1941 70
- Operation 5-21MN1941 71
- 5.6.1 Testing the output 72
- Operation 5-23MN1941 73
- 5-24 Operation MN1941 74
- Operation 5-25MN1941 75
- 5-26 Operation MN1941 76
- Operation 5-27MN1941 77
- 5-28 Operation MN1941 78
- Operation 5-29MN1941 79
- 5.8.2 Underdamped response 80
- 5.8.3 Overdamped response 81
- 5-32 Operation MN1941 82
- 5.9.1 Calculating KVELFF 83
- 5-34 Operation MN1941 84
- Operation 5-35MN1941 85
- 5.9.2 Adjusting KPROP 86
- Operation 5-37MN1941 87
- 5-38 Operation MN1941 88
- Operation 5-39MN1941 89
- 5-40 Operation MN1941 90
- 6.1 Introduction 91
- 6.2 NextMove e100 ind icators 92
- 6.2.3 ETHERNET LEDs 93
- 6.2.4 Communication 94
- 6.2.5 Motor control 94
- 6.2.6 Mint WorkBench 95
- 6.2.7 Ethernet 96
- 6.2.8 CANopen 96
- Troubleshooting 6-7MN1941 97
- 6-8 Troubleshooting MN1941 98
- 7.1 Introduction 99
- 7.1.4 Digital inputs 100
- 7.1.5 Digital outputs 100
- 7.1.6 Relay output 100
- 7.1.7 Stepper control outputs 101
- 7.1.8 Encoder inputs 101
- 7.1.9 Serial port 101
- 7.1.10 Ethernet interface 101
- 7.1.12 Environmental 102
- 7.1.13 Weights and dimensions 102
- 7.1.11 CAN interface 102
- A.1 Cables 103
- A.1.3 24 V power supplies 104
- B.1 Outline 105
- B-2 CE Guidelines MN1941 106
- Comments 111
- Comments MN1941 112
Produits connexes et manuels pour Serveurs Axis E100
Serveurs Axis APPINT Manuel d'utilisateur
(60 pages)
(60 pages)
Serveurs Axis 850 Manuel d'utilisateur
(10 pages)
(10 pages)
Serveurs Axis 2400AM Manuel de service
(112 pages)
(112 pages)
Serveurs Axis 7100 Spécifications
(20 pages)
(20 pages)
Serveurs Axis 70 Manuel d'utilisateur
(175 pages)
(175 pages)
Serveurs Axis 7100 Guide de l'utilisateur
(31 pages)
(31 pages)
Serveurs Axis E100 Manuel d'utilisateur
(7 pages)
(7 pages)
Serveurs Axis 7100 Manuel d'utilisateur
(181 pages)
(181 pages)
Serveurs Axis 7100 Manuel de service
(74 pages)
(74 pages)
Serveurs Axis 7100 Guide d'installation
(424 pages)
(424 pages)
Serveurs Axis 70 Guide de l'utilisateur
(24 pages)
(24 pages)
Serveurs Axis 24HUM Manuel d'instructions
(80 pages)
(80 pages)
Serveurs Axis 7000/FX Manuel d'utilisateur
(134 pages)
(134 pages)
Serveurs Axis NAS 100 Manuel d'utilisateur
(108 pages)
(108 pages)
Serveurs Axis 950 Manuel d'utilisateur
(69 pages)
(69 pages)
Serveurs Axis APPINT Manuel d'utilisateur
(10 pages)
(10 pages)
Serveurs Axis 70U Manuel d'utilisateur
(26 pages)
(26 pages)
Serveurs Axis 700 Manuel d'utilisateur
(2 pages)
(2 pages)
Serveurs Axis E100 Manuel d'installation
(27 pages)
(27 pages)
MIDLITE POWER+PORT RECESSED RECEPTACLE KIT AND WIREPORT PL manuali
Manuali dei proprietari e guide per l'utente per Accessori per gli impianti elettrici MIDLITE POWER+PORT RECESSED RECEPTACLE KIT AND WIREPORT PL.
We fornisce 1 manuali pdf MIDLITE POWER+PORT RECESSED RECEPTACLE KIT AND WIREPORT PL per scaricare gratuitamente in base al tipo di documento: Manuale Utente
Midlite POWER+PORT RECESSED RECEPTACLE KIT AND WIREPORT PL Manuale Utente (1 pagine)
Marchio: Midlite | Categoria: Accessories for electrical | Dimensione: 0.93 MB |
Indice
Più prodotti e manuali per Accessori per gli impianti elettrici MIDLITE
| Modelli | Tipo di Documento |
|---|---|
| POWER+PORT KIT—HDTV POWER SOLUTION WITH 6 FT CORD |
Manuale Utente
Midlite POWER+PORT KIT—HDTV POWER SOLUTION WITH 6 FT CORD User Manual,
1 pagine
|
| POWER JUMPER HDTV POWER RELOCATION KIT |
Manuale Utente
Midlite POWER JUMPER HDTV POWER RELOCATION KIT User Manual,
1 pagine
|
| POWER+PORT KIT—HDTV POWER SOLUTION WITH 3 FT CORD |
Manuale Utente
Midlite POWER+PORT KIT—HDTV POWER SOLUTION WITH 3 FT CORD User Manual,
1 pagine
|
| SPLITPLATE RECESSED POWER INLET |
Manuale Utente
Midlite SPLITPLATE RECESSED POWER INLET User Manual,
2 pagine
|
| SMART STRIP |
Manuale Utente
Midlite SMART STRIP User Manual,
1 pagine
|
| IN-LINE SURGE AND LIGHTNING SUPPRESSOR WITH RFI FI |
Manuale Utente
Midlite IN-LINE SURGE AND LIGHTNING SUPPRESSOR WITH RFI FILTERING User Manual,
2 pagine
|
| POWER ADAPTER CORD |
Manuale Utente
Midlite POWER ADAPTER CORD User Manual,
1 pagine
|
| POWER+PORT POWER CORD |
Manuale Utente
Midlite POWER+PORT POWER CORD User Manual,
3 pagine
|
| DOUBLE GANG SPLITPORT |
Manuale Utente
Midlite DOUBLE GANG SPLITPORT User Manual,
2 pagine
|
| CABLE VENT |
Manuale Utente
Midlite CABLE VENT User Manual,
1 pagine
|
© 2020, manymanuals.fr. Tous droits réservés | 0.022 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels