Axis Print Server 5470e Manuel d'utilisateur Page 86
- Page / 267
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Section 5: Setting Up - IBM Mainframe AXIS 5470e User’s Manual
86
JES3 Initialization Below is sample JES3 statements for an TCP/IP attached AXIS 5470e.
In the example the JNAME=PRT1 has been used.
Note:
The following paragraphs describe the JES3 initialization statements
shown above, which are typical of the JES3 statements used with
PSF. For more detailed descriptions of all JES3 initialization
statements, refer to the JES3 initialization and tuning publication for
your operating system.
PRTnnnn Statement Explanation
PRMODE
Specifies the data-set processing modes supported for the printer. It lists all the PRMODE values that the
printer accepts. If the AXIS 5470e is connected to a PostScript printer, the correct setting is
PRMODE=(PAGE,LINE,).. This setting indicates that composed-page and line data sets can be
printed.
SEP
Enables job-header and job-trailer separator pages to be produced.
Note1: If the Distributed Print Function (DPF) of PSF/2 is installed, you may need to set
this parameter to
YES.
Note2: This parameter is new in JES2 and replaces the SEP | NOSEP parameter.
SEPDS
Enables formatted data-set header separator pages to be produced.
Note: This parameter is new in JES2 and replaces the SEPDS | NOSEPDS parameter.
START
Specifies the way that the printer is started. The parameter value NO specifies that the printer is to be started
by an operator command. The parameter value
YES specifies that the printer, if it is ready, is to start
automatically when JES2 starts processing.
Note: This parameter is new in JES2 and replaces the DRAIN | START parameter.
TRKCELL
Specifies whether track-cell despooling is to be used or not. It is recommended to set this parameter to YES.
UCS
Specifies a default font. If you want to select a font in the startup procedure instead of the JES2 default font,
you should set this parameter to
0.
FSSDEF,TYPE=WTR,FSSNAME=FSS3,PNAME=SAMPPRO3,SYSTEM=SYS1,TERM=NO
DEVICE,DTYPE=PRTAFP1,JNAME=PRT1,JUNIT=(,SYS1,,ON),FSSNAME=FSS3
MODE=FSS,PM=(LINE,PAGE,),CHARS=(YES,GT12),
CARRIAGE=(TES,A868),CKPNTPG=100,HEADER=YES,WC=(C)
This is only an example. For specific coding for JES parameters, refer to the JES
publication for the level of JES you are using.
- AXIS 5470e 1
- Network Print Server 1
- AXIS 5470e User’s Manual 2
- Section 1 Introduction 7
- Where to use it 8
- How to use it 9
- AXIS 5470e User’s Manual 10
- Section 2 Product Overview 12
- AXIS Product CD 13
- Section 3 Basic Installation 15
- Installation Guide 17
- Assigning an IP address 20
- Setting the IP address 22
- Manual IP address assignment 24
- Server menu 25
- UNIX, Mac OS X 26
- Section 4 Setting Up - AS/400 31
- SNA Printing - 5494 Mode 32
- DSPNETA 33
- CONTROLER1 35
- CONTROLER2 35
- Display System Value 37
- QUSER Status is *ENABLED 39
- *NOMAX. Press F3 39
- Configuration’ window 45
- SNA Printing 55
- GID=1, FID=1, GRPNM=gggggg 57
- Switched major 59
- TCP/IP TN3270E Printing 64
- General Settings 65
- 6. Click OK 68
- TCPIP. For a full 78
- Device Statement Explanation 89
- Example continues 92
- $Pprinter-name 95
- *VARY printer-name, OFF 95
- *CANCEL printer-name 95
- Setup using NDPS 97
- Queue-based Printing Methods 102
- NetWare Packet Signature 103
- AXIS Print Monitor Overview 106
- Windows NT 3.5x 107
- Section 8 Setting Up - OS/2 117
- NetBIOS/NetBEUI Printing 118
- Installation in Mac OS X 122
- Choosing a Printer 123
- Section 10 Setting Up - UNIX 128
- Using a Web browser 135
- “100 MBIT” or “Auto-Sense” 139
- Using FTP 145
- Example: 146
- (not visible) 146
- Using Telnet 148
- Using SNMP 152
- Using HP administration tools 153
- Using Novell Utilities 154
- (Internet Printing Protocol) 158
- Overview 158
- User Requirements 161
- Firewall Considerations 161
- How to print 161
- 0A) with an 173
- Communication Parameters 183
- Mainframe Specific 185
- Parameters 185
- AS/400 Specific 185
- Updating parameters 186
- Section 16 SNA Gateways 190
- 0123 4565 197
- Section 18 IBM Fonts 198
- Twinax Printer 206
- Emulations 206
- Coax mode 207
- Mainframe 207
- Section 20 IPDS Overview 211
- IPDS Fonts 219
- Printer Resident Fonts 219
- Immediate Font Substitutions 220
- Unsupported Fonts 220
- Typographical Fonts 221
- Section 21 DBCS Support 222
- Configuring the AXIS 5470e 223
- Amending Device Features 225
- Font Tables 226
- Section 23 The Parameter List 231
- (Requires Restart) 235
- (MPL, MPP, CPI, LPI, LM, TM) 237
- (Courier when not specified) 237
- Section 24 Test Button 248
- Section 26 Glossary 254
- server as soon as 256
- AXIS 5470e User’s Manual 261
Produits connexes et manuels pour Imprimer et scanner Axis Print Server 5470e
(30 pages)
(34 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.098 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels